ViewMAX SMIL-Player Configuration: Unterschied zwischen den Versionen

Aus netMAX Wiki
Wechseln zu: Navigation, Suche
(→‎SMIL-R Player/Display (2nd. Generation))
 
Zeile 18: Zeile 18:
 
All devices
 
All devices
 
#Please wait until the device has started
 
#Please wait until the device has started
−
#configure the network under ''/advanced/network/'' (Default is DHCP).
+
#Configure the network under ''/advanced/network/'' (Default is DHCP).
−
#Richten Sie im viewMAX Director unter ''/Configuration/Displays'' das neue Gerät ein - Die Tastenkombination (''Strg+Shift+C'' aktiviert den Menüpunkt ''Configuration'' im Hauptmenü).  
+
#In the viewMAX Director setup the new device under ''/Configuration/Displays''- (''Ctrl+Shift+C'' activates the menu item ''Configuration'' in the main menu).  
−
#Konfigurieren Sie den Typ ''REST'' mit dem Benutzer ''admin''. Sollten Sie am Player/Display ein Kennwort hinterlegt haben, so geben Sie dieses bitte mit an.
+
#The device type is ''REST'' with the user ''admin''. If you set up a device password, you also have to enter it here.
−
#Über den ''viewMAX Director/Utilities/Director Display Access'' bespielen Sie das Display mit einem ersten Bild.
+
#With the ''viewMAX Director/Utilities/Director Display Access'' send an initial picture to the device.
  
−
'''Führen Sie die folgenden Schritte bitte erst aus, wenn das Display bereits mit einem Bild bespielt wurde und dieses angezeigt wird.'''
+
'''Don't continue with the following steps, before the device shows your content.'''
  
−
Diese Einstellungen dienen dazu, dass nach einem Neustart, die letzten Inhalte wiedergeben werden.
+
With this settings the display will automatically display the latest content after a restart.
−
#Bewegen Sie den Mauscursor in eine Ecke des Bildschirms und drücken Sie die linke Maustaste bis das Konfigurationsmenü wieder erscheint.
+
#Move the mouse cursor to any corner of the screen and press the left mouse button until the configuration menu occurs.
−
#Wählen Sie nun ''Set Content:'' und geben die folgende URL an ''http://localhost:8080/v2/user-data/index.smil''
+
#Select ''Set Content:'' and enter the start URL ''http://localhost:8080/v2/user-data/index.smil''
−
#Starten Sie den Player/Display neu.
+
#Restart the device
  
  
−
=== Unter "Advanced / Content" ===
+
=== Further settings "Advanced / Content" ===
  
 
'''AppStart:'''
 
'''AppStart:'''
Zeile 45: Zeile 45:
 
'''FailSafe:'''
 
'''FailSafe:'''
  
−
URL bleibt leer, andere Felder wie unter Appstart
+
no changes
  
 
'''EasyPlay:'''  
 
'''EasyPlay:'''  
Zeile 53: Zeile 53:
 
'''Schedule:'''  
 
'''Schedule:'''  
  
−
Schalter A-E auf aus
+
Switches A-E off
  
−
== SMIL-A Player/Display (1. Generation, bis 2015) ==
+
== SMIL-A Player/Display (1st. Generation, until 2015) ==
 
Digital Signage Media Appliance  
 
Digital Signage Media Appliance  
  
 
Model XMP-3xxx, viewMAX 12 SMIL, viewMAX 17 SMIL, viewMAX 19 SMIL
 
Model XMP-3xxx, viewMAX 12 SMIL, viewMAX 17 SMIL, viewMAX 19 SMIL
  
−
Einrichtung wird nicht mehr unterstützt
+
Setup is any longer supported.

Aktuelle Version vom 22. Juli 2019, 17:28 Uhr

SMIL-R Player/Display (2nd. Generation)

Digital Signage Media Appliance Model MBR-1100, XMP-6250, XDS-1078 for viewMAX Software v2.7 and higher.

An USB mouse is mandatory for the player and display configuration. It is recommended to use an USB-Keyboard (an American keyboard driver is installed).

For an already prepared devices, move the mouse cursor to any corner of the screen and press the left mouse button until the configuration menu occurs. If a password was set, enter your password if requested.

The correct order of the First Steps is mandatory, otherwise it is not possible to send content to the device.

First Steps

Preparing a player

  1. Connect the player to a HDMI port of a display.
  2. Connect the power supply.

All devices

  1. Please wait until the device has started
  2. Configure the network under /advanced/network/ (Default is DHCP).
  3. In the viewMAX Director setup the new device under /Configuration/Displays- (Ctrl+Shift+C activates the menu item Configuration in the main menu).
  4. The device type is REST with the user admin. If you set up a device password, you also have to enter it here.
  5. With the viewMAX Director/Utilities/Director Display Access send an initial picture to the device.

Don't continue with the following steps, before the device shows your content.

With this settings the display will automatically display the latest content after a restart.

  1. Move the mouse cursor to any corner of the screen and press the left mouse button until the configuration menu occurs.
  2. Select Set Content: and enter the start URL http://localhost:8080/v2/user-data/index.smil
  3. Restart the device


Further settings "Advanced / Content"

AppStart:

URL: http://localhost:8080/v2/user-data/index.smil

Advanced

  1. Package Name: com.iadea.player
  2. Class name: com.iadea.player.SmilActivity
  3. Action: android.intent.action.VIEW
  4. Type:

FailSafe:

no changes

EasyPlay:

Disabled

Schedule:

Switches A-E off

SMIL-A Player/Display (1st. Generation, until 2015)

Digital Signage Media Appliance

Model XMP-3xxx, viewMAX 12 SMIL, viewMAX 17 SMIL, viewMAX 19 SMIL

Setup is any longer supported.

Von „http://wiki.netmax.de/index.php?title=ViewMAX_SMIL-Player_Configuration&oldid=1416“